RevoluzionAutomotive
All guides

AN fittings basics

AN fittings explained: what the dash numbers actually mean

The Army-Navy standard, why AN-6 is 3/8", and why AN is not the same as NPT.

The short version

  • The dash number is sixteenths of an inch: AN-6 = 6/16" = 3/8".
  • AN and JIC share a 37° flare but AN uses UNJ threads — they usually thread together, but AN is the controlled-spec part.
  • NPT is a tapered pipe thread that seals on the threads. AN seals on a 37° flare. Never mix the two without an adapter.

Video walkthrough coming soon

AN stands for Army-Navy — the standard the US military developed so that a hose fitting bought in one place would seal against one bought somewhere else, in the field, without a catalogue. That is the whole point of the standard: interchangeability. Every dimension is fixed, so any correctly made AN-6 hose end seals against any correctly made AN-6 adapter.

The dash number is just sixteenths of an inch

The number after the dash is the hose's inside diameter in sixteenths of an inch. AN-6 is 6/16", which is 3/8". That single rule answers most sizing questions before you reach for a caliper.

DashHose ID (in)Hose ID (mm)Typical threadCommon use
AN-33/16"4.83/8-24 UNFGauge lines, small returns
AN-41/4"6.47/16-20 UNFBrake lines, fuel feed on small engines
AN-63/8"9.59/16-18 UNFThe default fuel line size
AN-81/2"12.73/4-16 UNFFuel feed on turbo / high-power builds
AN-105/8"15.97/8-14 UNFOil coolers, fuel feed on big power
AN-123/4"19.11-1/16-12 UNFOil coolers, radiators, large fuel lines
AN-161"25.41-5/16-12 UNFRadiator, water, large oil systems
AN-201-1/4"31.81-5/8-12 UNFBig water and oil circuits

One catch: the dash number describes the hose bore, not the thread. The thread is always larger than the bore — an AN-6 fits a 3/8" hose but its nut is 9/16" across the threads. If you are measuring a fitting you already have, you are measuring the thread, and you have to read it off a chart rather than assume it matches the bore.

AN is not NPT, and the difference matters

This is the mistake that costs people a weekend. The two families seal in completely different ways:

  • AN / JIC seals on a 37° flare face that is crushed against a matching cone. The threads only clamp. No sealant, ever.
  • NPT is a tapered pipe thread that seals by interference between the thread flanks. It needs a sealant (PTFE paste, not tape) and it deforms slightly each time it is tightened.
  • ORB (O-ring boss) is a straight thread with a flat face and an O-ring — the O-ring seals, the thread clamps. Common on pumps, filters and fuel rails.

Screwing an AN flare into an NPT port will physically start threading on some sizes and will never seal. If a joint is leaking at the threads rather than the flare, you have the wrong family — not a torque problem.

AN vs JIC: same 37°, different thread spec

AN and JIC are dimensionally interchangeable at the flare — both are 37°. The difference is the thread: AN calls for a UNJ thread (a controlled root radius that increases fatigue life), JIC calls for a standard UNF thread.

In practice they thread together and hold. The practical consequence is about provenance: AN is the controlled aerospace specification, so an AN-marked part has documented material and tolerances. A no-name "JIC" part may be perfectly good or may be soft aluminium with a badly cut flare. Buy from someone who will tell you what the material is.

Why 37° and not 45°

45° is the older SAE flare, still found on some American plumbing and industrial gear. A 45° flare against a 37° cone contacts on a line rather than a face, which will seal at low pressure and weep at high pressure. They look almost identical in a photo. Check with a flare gauge if you are unsure — it is a two-second check that saves a fuel leak.

What to buy first

If you are building a fuel system from scratch, most Malaysian builds land on AN-6 for the feed line, AN-6 or AN-8 for the return depending on pump size, and AN-4 for brake lines. Buy one spare of each fitting you use — the postage on a second order always costs more than the spare.

Next guide

AN vs JIC vs NPT: which one is on my car?